99V久久综合狠狠综合久久,久久99这里只有是精品6,久久久99精品成人片

<u id="aaejl"></u>
  • <th id="aaejl"><option id="aaejl"></option></th>
    <th id="aaejl"><video id="aaejl"></video></th>
    1. <th id="aaejl"><option id="aaejl"></option></th>

      <th id="aaejl"></th>

      1. <strike id="aaejl"></strike>
      2. Favorite | Home Page | 中文版

        Address:Quanzhou Licheng District Jiangnan High-tech Park, Love Street, Building terracotta clear 2-2
        Tel:0595-22421239
        Fax:
        Phone:13505999802
        Contact:Mr.Xu

        Your Location:Home > News > Industry news News

        The choice of adhesive
        Category:Industry news   Publish:2015-02-12 00:00:01   View:1167次 [Back]
          Adhesive options
        Due to the function of the adhesive is you want a specific strong and durable ceramic tiles pasted on the established grass-roots, so the adhesive of choice will depend on the combination of two bonded materials, as well as the adhesive systems are subject to in its specific service environment load type. Fortunately, our JC/T547-2005 (Crystal ISO13007:2004 1th, part 2) adhesives for ceramic tiles in 19 models embodied the world peers in Exchange for decades in the run-in to these complex combinations of service countermeasures of consensus. For example, the lateral deformation of cement-based adhesives, S1, S2 has been shown to counterbalance the cyclic loads and impact of effective performance.   
        Good adhesive as thin as possible in principle valid, so ceramic tile adhesive in the application really depends on the thickness of the base and the smoothness of ceramic tiles and ceramic tile size. General requirements of the grass-roots level using 2?m a ruler to measure the tolerance does not exceed 3?mm; ceramic tile thickness should also be less than 10%. This way, the thickness of the adhesive between the 2~6?mm. For example, 2?mm thick adhesive to paste the 50?mm?x?50?mm mosaic. However, if the AI fine extruded ceramic tiles, for example, surface roughness GB the maximum allowable variation is 0.8%. Then, a 800?mm?x?800?mm brick is allowed from the datum plane deviation 9?mm, design 10?mm thickness of the adhesive is not conservative.   
          Adhesive options
        Due to the function of the adhesive is you want a specific strong and durable ceramic tiles pasted on the established grass-roots, so the adhesive of choice will depend on the combination of two bonded materials, as well as the adhesive systems are subject to in its specific service environment load type. Fortunately, our JC/T547-2005 (Crystal ISO13007:2004 1th, part 2) adhesives for ceramic tiles in 19 models embodied the world peers in Exchange for decades in the run-in to these complex combinations of service countermeasures of consensus. For example, the lateral deformation of cement-based adhesives, S1, S2 has been shown to counterbalance the cyclic loads and impact of effective performance.   
          Typical selection of combination binder of
          Combined condition of adhesive? typical grade
          Rigid indoors (such as concrete) laying on the ground, high water absorption of stoneware pottery in C1
          Rigid indoors (such as reinforced concrete) wall laying, high water absorption of stoneware pottery in C1T
          Old ceramic tile surface in the Office laying porcelain tiles with low water absorption C2
          In the context of long-term flooding of laying ceramic tile C2
          Laying ceramic tiles on the outside wall of reinforced concrete C2TE
          Metro station, Elevator vibration loads, such as a strong sense of place to lay ceramic tile C2S1
          Lobby, the airport restaurant at the mall a quick refurbishment of large-size ceramic tile floor C2F
          Laying ceramic tiles on the Interior light partition Board D2T?, C2TS1
          In a stainless steel pool swimming pool tiles laying on R2T
        Good adhesive as thin as possible in principle valid, so ceramic tile adhesive in the application really depends on the thickness of the base and the smoothness of ceramic tiles and ceramic tile size. General requirements of the grass-roots level using 2?m a ruler to measure the tolerance does not exceed 3?mm; ceramic tile thickness should also be less than 10%. This way, the thickness of the adhesive between the 2~6?mm. For example, 2?mm thick adhesive to paste the 50?mm?x?50?mm mosaic. However, if the AI fine extruded ceramic tiles, for example, surface roughness GB the maximum allowable variation is 0.8%. Then, a 800?mm?x?800?mm brick is allowed from the datum plane deviation 9?mm, design 10?mm thickness of the adhesive is not conservative.

        Copyright © 2015 Quanzhou Jinyuan special adhesive tape Ltd. Support:12T.CN 閩ICP備******號
        點擊關閉
        • 1212
          sd12
        99V久久综合狠狠综合久久,久久99这里只有是精品6,久久久99精品成人片